Ask Proxima M8 Guía de usuario

Downloaded From projector-manual.com ASK Manuals

9Configuring Advanced Projector SettingsYour projector has a setup menu that you can use to configure advanced settings.Displaying the Setup MenuPress

10Basic Setup Menu ExampleThe procedure below shows how to configure the following three settings:• Image Adjustment J Contrast• Image Adjustment J Co

11To configure the “Option Settings 1 J Eco Mode” setting5Press the [ESC] key.6Press the [T] key three times to select “Option Settings 1”.7Press the

12You can use the procedures in this section to restore all of the settings on a particular main menu or all of the settings on the setup menu to thei

13To restore all settings on the setup menu to their initial factory defaults1Press the [MENU] key to display the setup menu.2Use the [T] key to selec

14Image Adjustment Main MenuSetting Name InputSetting UnitDescriptionBrightness RCVU Source SpecificUse this sub-menu to adjust the brightness of the

15Vertical PositionRCV Signal SpecificUse this sub-menu to adjust the vertical position of the input source image within the projection area. Horizont

16About the “Signal Specific” Setting UnitFor the items that have “Signal Specific” in the “Setting Unit” column of the above table, the setting is sa

17Projection ModeRCVUN Single Use this sub-menu to specify whether projection will be from the front of the screen or the back of the screen. *:Select

18Blank Screen RCVUN Single Use this sub-menu to specify what should be projected after the [BLANK] key is pressed. Blue:Select this option to project

1ContentsContents... 1About this manual... ...

19Input Settings Main MenuSetting Name InputSetting UnitDescriptionRGB Input RCUVN Single Use this sub-menu to specify manually the type of signal bei

20Option Settings 1 Main MenuSetting Name InputSetting UnitDescriptionMenu Position RCVUN Single Use this sub-menu to specify the display position of

21Direct Power OnRCVUN Single Use this sub-menu to turn Direct Power On on or off. See “Direct Power On” in the “User’s Guide” for more information. O

22Option Settings 2 Main MenuSetting Name InputSetting UnitDescriptionZoom Memory RCVUN Single Use this sub-menu to turn zoom memory on or off. Zoom m

23Operational Info Main MenuSetting Name InputSetting UnitDescriptionLamp Time RCVUN Single This sub-menu item shows the cumulative number of hours th

24Restore All Defaults Main MenuSetting Name InputSetting UnitDescriptionRestore All DefaultsRCVUN Single This sub-menu returns all sub-menu items on

25User MaintenancePeriodically clean the projector exterior, lens, intake vents, and exhaust vents on a regular basis.Important!z Always make sure tha

26Important!z Continued use of the projector after dust has accumulated around the intake vents can cause overheating of internal components and lead

27When to replace the lampThe LAMP indicator starts to flash red and the message shown below appears whenever the lamp time exceeds 2000 hours.When th

28To replace the lampImportant!When replacing the lamp, use the special screwdriver that comes with the YL-33 replacement lamp. The projector does not

2Replacing the Lamp ... 26To check the current lamp use time...

296Use the lamp cartridge handle to pull the lamp cartridge from the projector.7Insert the new lamp cartridge as far as it will go, as shown in the il

30To reset the lamp time1Turn on the projector.2Press the [MENU] key to display the setup menu.3Press the [T] key to select “Operational Info”, and th

31AppendixWhen performing an operation on the remote controller, point it at the remote control signal receiver on the back or front of the projector.

32Some video devices are equipped with a component video output terminal. You can use an optionally available VESA to component video adapter (SP-VESA

33Full-screen Display of an RGB ImageThe projector outputs images using XGA (1024 pixels × 768 pixels) video resolution. When the input signal from th

34Use the following procedure to replace the lens cover if it should accidentally become detached from the projector. 1Insert the nub () of the left

3Operation During ProjectionThis section explains the various types of operations you can perform while the projector is projecting an image. You can

4Selecting the Color ModeYou can select from among five different color mode settings to optimize the projected image in accordance with image content

5Momentarily Cutting Off the Input Source Image1Press the [BLANK] key.z This temporarily cuts off the image from the input source and projects a black

6Displaying a Pointer in the Projected ImageYou can select from among eight different pointer styles, including various arrow styles, for display in t

7Press the [ASPECT] key to toggle the aspect ratio of the displayed image between 4:3 and 16:9.Notez The aspect ratio setting affects the projected im

8Pressing the [FUNC] key displays the menu shown below.You can use this menu to perform the operations described below. z Adjust image brightnessHighl